# Audio and music

Source: https://frameleaf.app/docs/studio/audio/

Good sound makes a film. Studio keeps your camera sound, music and voice on separate tracks, so you can balance them until everything sits just right.

## Clip sound

For each clip you can set:

- **Volume**, in decibels, or mute the clip
- **Fade in** and **fade out**
- **Pitch**, in semitones and cents
- **EQ**

## Track and master sound

- Each track has a **fader**, **pan** and its own **EQ**, and can be muted or soloed.
- The **master** controls the whole mix's level and mute, separately from your computer's volume.
- **Ducking** lowers the music while a voice-over plays. To balance speech and music for you, see [Voice over music](#voice-over-music).

Watch the meters while you play, then export a short sample to hear the final mix before a long export.

## Match loudness

Clips recorded on different cameras and phones rarely sit at the same level. **Match loudness** brings dialogue to a consistent loudness in one step. In the web editor:

1. Select the clips to match, then open **Match loudness** in the audio panel.
2. Check the **Target** loudness (−16 LUFS to start) and the **Peak ceiling** (−1 dBTP to start).
3. Select **Analyze**. Studio measures each clip as it plays in your edit and shows how loud it is now and its peak.
4. Review the suggested change for each clip, then select **Apply**. All the changes are one step to undo.

Matching changes each clip's volume only. Fades, volume changes over time and ducking keep their shape, and it can't repair a distorted recording. Studio won't suggest a boost above +12 dB, so very quiet clips are flagged for you to review by hand, as are muted, silent and very short clips. If you edit a clip after measuring, analyze it again.

The target and ceiling are saved with the project, so the export check below uses them too.

## Voice over music

**Voice over music** sets your voice tracks to a steady loudness and lowers the music while someone speaks, so speech stays clear. In the web editor:

1. Select a clip with sound and open the **Audio** tab in the clip panel. **Voice over music** sits below the clip's own sound controls.
2. Choose the **Voice tracks** and **Music tracks**. Voice and music need different tracks, and the same clip can't be on both.
3. Select **Review mix**. Studio measures your voices as they play in your edit and shows what will change in plain words, such as how far the music drops while someone speaks and how much louder or quieter each voice track gets.
4. Select **Listen to 15 seconds** to hear the new mix from the playhead. **Stop listening** ends it, and nothing on the timeline changes.
5. Select **Apply**. You can undo it in one step.

Most mixes need nothing more. To fine-tune, open **Advanced** for **Voice loudness (LUFS)**, **Music level while someone speaks (dB, below 0)**, and how quickly the music dips and returns with **Fade down (s)** and **Fade back up (s)**. With Advanced open, the review also shows the measured numbers.

Your clip volumes, fades and keyframes stay as they are, and so do the master volume and the limiter. Any ducking already set on the voice clips, including which tracks it lowers, is replaced by this mix. Listening and the export use the same ducking, so what you hear is what you get.

Turn off solo first, and unlock the tracks you choose. If you change the film after reviewing, review the mix again before applying.

### Limit peaks on export

Turn on **Limit true peaks at the ceiling on export** to keep the finished mix from going over the peak ceiling. The limiter is the last step of the export mix, after the master volume. While it's on, playback in the editor uses a close approximation, so the export is the reference.

## Music

Add a music file from your library as a music bed on the music track, or make new music for your project.

### Make new music

Studio can write new music for your project. Open the editor's **AI** panel, pick one of the music presets and generate it. Studio shows its progress, and you can cancel at any time. The finished music goes on your timeline like any other audio.

Music is made on your Frameleaf server or a computer at home that can make it, never on Frameleaf Cloud. [Make a movie](https://frameleaf.app/docs/studio/make-a-movie/) uses the same music for its **Made for this movie** choice.

### Your own music

Frameleaf doesn't include a library of songs, so for your own tracks bring music you have the rights to use.

## Voice-over

Record a voice-over with your microphone, or [generate one from text](https://frameleaf.app/docs/studio/captions/#voice-over), and Studio places it on the voice track.

## Clean up voice

Remove wind, hum, background noise and room echo from a clip's sound, compare before and after, and keep the original. See [Clean up voice](https://frameleaf.app/docs/studio/clean-up-voice/).

## Tidy up speech

Studio finds silences and filler words such as "um" and offers to remove them. You review every suggestion before anything changes. To cut by the words themselves, see [Edit by transcript](https://frameleaf.app/docs/studio/edit-by-transcript/).

## Sound in the export

Export a short part of the film first to hear the final mix: the export dialog's **Range** lets you choose part of the film. To export the sound alone, choose one of the **Sound only** formats. After the export, Studio reports how loud it came out. See [Exporting](https://frameleaf.app/docs/studio/exporting/#audio).
